|
Nienawidzę być kurą domową
|
Temat: Bład podczas podłaczenia programatora sob4n, AVRprog właśnie szuka programatora tylko na COM1-4. Źródło: dioda.prohost.pl/forum/viewtopic.php?t=3642
Temat: Jak najtaniej zająć się programowaniem? Możliwe, że chodziło o ten opis: http://radzio.dxp.pl/ avrprog/
Nie posiadam portu LPT, mam jeden port COM rs232 i właśnie dysponując tym portem chciałbym zapragromować attiny2313. Tak więc programator nie może posiadać mikrokontrolera, bo nie miał bym go jak zaprogramować. Czy istnieje możliwość budowy takiego programatora? Źródło: edw.com.pl/forum/viewtopic.php?t=8427
Temat: Czy da się programować AVT3500 przez COM1? http://radzio.dxp.pl/avr910.htm - to prosty programator pracujący na porcie COM lub USB z odpowiednią przejściówką. Koszt jego wykonania powinien się zamnąć w 15zł.
http://radzio.dxp.pl/ avrprog/ - to trochę bardziej rozbudowany, ale o większych możliwościach. Szybszy niż poprzedni i programuje więcej mikrokontrolerów (wszystkie w AVRy trybie ISP i kilka szeregowych 8051). Koszt wykonania nie powinien przekroczyć 30zł.
http://www.lancos.com/siprogsch.html - to już zupełnie prosty, bez żadnych mikrokontrolerów, ale nie będzie współpracował z przejściówkami USB. Źródło: edw.com.pl/forum/viewtopic.php?t=3514
Temat: Problem z połączeniem Spróbuj zaprogramować układ innym programem np AvrProg.
Nie długo ukarze się artykuł właśnie na temat problemów z programowaniem, więc jak Ci się nie uda, to może tam coś znajdziesz Źródło: dioda.prohost.pl/forum/viewtopic.php?t=1331
Temat: Programator USB AVR ISP II STK500 STK500v2 Domyślam się, że jest to programator AVRProg USB v2.
Zgodnie z zaleceniem w komunikacie ściągnij nowe drivery ze strony ANDiTECH
mnie to pomogło, ale nie używałem go pod w7 64-bit.
Spróbuj driverów pod Viste, lub ustaw kompatybilność z którąś z wcześniejszych wersji okienek. Źródło: dioda.prohost.pl/forum/viewtopic.php?t=3598
Temat: Czym programujecie uC Piszcie tu o tym jakich używacie programów do przesyłania plików do uC i jakich programatorów.
Ja używam stk200/300 ale już do mnie jedzie programator na USB.
Do przesyłania programu używałem Bascoma ale na 80% przejde teraz na AvrOspII lub na AVRProg'a. Źródło: dioda.prohost.pl/forum/viewtopic.php?t=214
Temat: Czym programujecie uC Program AVRstudio 4.17. w chwili obecnej.
A co do programatorów to kiedyś zaczynałem z równoległym programatorem - konstrukcja kolegi
(był pod bascoma 8051)
W chwili obecnej używane programatory to:
- stk200/300 (kilka miechów temu wyszedł z użycia zastąpiony przez te następne)
- chwilowo USBasp ale program AVRDude mi nie odpowiadał i sprzedałem
- USB AVRISP
- AVRDragon
- JTAGICE mk II
na użytek zajęć dydaktycznych:
- USB AVRprog v2 - z AVRstudio widoczny jako STK500
- ZL2PRG - w sumie to to samo co STK200
- JTAG ZL16PRG
zestawy uruchomieniowe na użytek zajęć:
- ZL3AVR,
- ZL11AVR,
- najczęściej jednak stara, poczciwa płytka stykowa z dorobionymi swoimi przejściówkami
oraz układami IO w postaci płytki 8 switchy, klawiatury matrycowej, płytek z 8 diodami LED itd.
Ze wszystkich programatorów najbardziej polecam Dragona
Relatywnie tani, dla... Źródło: dioda.prohost.pl/forum/viewtopic.php?t=214
Temat: Pytanie o programator zgodny z stk500v2 Witam
Obawiam się że ten z elektrody nie będzie kompatybilny i nie można będzie go upgradować. Może lepiej zrób ten http://radzio.dxp.pl/ avrprog/ Źródło: edw.com.pl/forum/viewtopic.php?t=4991
Temat: Część 1-Kurs programowania uC AVR w C (WinAVR, Kurs AVR-GCC) Ja polecam użyć AVRprog Źródło: dioda.prohost.pl/forum/viewtopic.php?t=1312
Temat: ATMEGA32 z rezonatorem kwarcowym o częstotliwości 16MHz Napisz czym programujesz (jakim programem wgrywasz kod do mikrokontrolera). W AVRProg-u wygląda to tak : Źródło: edw.com.pl/forum/viewtopic.php?t=2841
Temat: Bascom na usb Kupiłem programator AvrProg USB taki jak pokazany jest w kursie programowania avr w C udostępniony na tym forum. Nie wiem jak zaprogramować attiny2313 w języku Basic. W jakim programie można go programować. Może ktoś będzie umiał mi pomóc. Z góry dziękuje Źródło: dioda.prohost.pl/forum/viewtopic.php?t=1349
Temat: z USB na LPT przy pomocy procka (tiny2313) zrobic konwerter sygnalu z RS232 na LPT. Chcialem sie dowiedziec czy duzy jest koszt wykonania czegos takiego?
AVR910 to prosty programator ISP podłączany pod port szeregowy. Można łatwo podłączyć pod USB wykorzystując przejściówkę do telefonów komórkowych (choćby od SE T68i).
Poczytaj sobie: http://radzio.dxp.pl/avr910.htm
O kopii STK500: http://radzio.dxp.pl/ avrprog/ Źródło: edw.com.pl/forum/viewtopic.php?t=4554
Temat: Problem przy programowaniu A spróbuj innymi programami:
- AvrProg
-avrdude
-AvrOspII
-ISP Programmer Adama Dybkowskiego
Z góry mówię, że nie wiem czy wszystkie z nich obsługują Twój programator, ale warto spróbować. Źródło: dioda.prohost.pl/forum/viewtopic.php?t=1174
Temat: Poszukuję AVRprog'a w jak najnowszej wersji. Jak w temacie wiadomości, szukam i szukam na googlach i na innych i nie mogę znaleźć najbardziej odpowiedniej mi wersji. A mianowicie:
poszukują programu AVRprog, który obsługuje mikrokontrolery ATMega8.
Proszę pomóżcie! Pilne! Źródło: edw.com.pl/forum/viewtopic.php?t=1691
Temat: AVRProg USB i BASCOM AVR Witam kilka dni temu zakupiłem AVRProg USB i z AvrOspII działa poprawnie, natomiast w BASCOMie mogę odczytać Flasha, ale kiedy przechodzę do zakładki fusebit i klikam refresh dioda na krótko zapala sie na czerwono, a dopiero po chwili(już przy zielonej) "odzczytuje" fusebity niepoprawnie - SAME ZERA. Z którą wersją Bascoma Źródło: and-tech.pl/forum/viewtopic.php?t=34
Temat: Programowanie AT90CAN32 z AVRProg-USB Jak zaprogramować AT90CAN32 programatorem AVRProg-USB? Chciałbym używać AVRStudio ale po wyborze Tools -> AVR Prog nie ma na liście obsługiwanych procesorów AT90CAN32. Natomiast w instrukcji programatora jest na liście obsługiwanych procków. Może w innym środowisku sie da, tylko w jakim?? Źródło: and-tech.pl/forum/viewtopic.php?t=139
Temat: Problem "No supported board found. AVRprog version 1.40 Powyzszy komunikat oznacza iz probram Avrprog nie znalazl naszego programatora
W celu znalezienia przyczyny musimy sprawdzic na jakim porcie Com zostal zainstalowany programator (menadzer urzadzeń) jesli okaze się ze programator jest zainstalowany na Com5 albo wyższym należy zmienic port na niższy (od Com1 do Com4) lecz zwracając uwage zeby nie wybrać portu, który jest już w użyciu (jesli od Com1 do Com4 sa zajęte to należy najpierw jeden z nich np. Com3 przenieść na wyższy... Źródło: and-tech.pl/forum/viewtopic.php?t=7
Temat: Bład podczas podłaczenia programatora ...co by nie kliknąć to program się zawiesza i nie pozostaje nic innego jak zamknąć go poprzez menadżer zadań
8. Jeśli nie BASCOM to możne poprzez AVR STUDIO [ no to do roboty ]
Odpalam program wczytuje wczesnij zapisany programik klikam ikonkę profesorka z napisem AVR i pokazuje mi się okienko z połączeniem ...
Wybieram STK500 i port com5... Connect
Pojawia się okienko i Error
I tak na każdej zakładce .....
9. Próbowałem tez poprzez AvrProg:
Nie mam już pomysłów co możne być złe ... próbowałem reinstalować sterowniki i wgrywać inne wersje programów ale bez zmian na lepsze
Może ktoś spotkał się już z takim problemem ?? Przeszukałem forum ale nie znalazłem odpowiedzi, a jeśli były jakieś wskazówki to i tak to nic nie pomagało.
Programator mam podłączony z podstawka za pomaca taśmy 2 x 5 pin nie zauważyłem tam nic niepokojącego.
Dziękuje... Źródło: dioda.prohost.pl/forum/viewtopic.php?t=3642
Temat: Turnigy 9X - nowy software ...programator z możliwością zasilania układu programowanego (np jak ten wspomniany wcześniej) to możemy przetestować naszą pracę.
1) Upewniamy się że połączenia są właściwe. Należy zwrócić szczególną uwagę na linie GND i Vcc ! Sprawdzić co najmniej 2 razy!!!
2) Ustawiamy zworki programatora tak jak na zdjęciu (tylko jedna odpowiedzialna za zasilanie układu)
3) Sprawdzamy na jakim porcie COM zainstalował się programator ( AVRprog USB v2)
4) Wykonujemy komendę (skąd ją wziąć - w poście SOFTWARE)
avrdude.exe -pm64 -c stk500v2 -P com3 -n
gdzie com3 zastępujemy ustalonym wcześniej portem. Uwaga czasami może to chwilę potrwać więc nie denerwujemy się za szybko.
5) Jeżeli dostaniemy coś takiego:
avrdude.exe: stk500_2_ReceiveMessage(): timeout
avrdude.exe: AVR device initialized and ready to accept instructions
Reading |... Źródło: pfmrc.eu/viewtopic.php?t=25564
Temat: Bład podczas podłaczenia programatora Z tego co słyszałem to najlepiej podłączać pod COM1 - 4 spróbuj zmienić port i zobacz wtedy
Zmieniłem port na " com4 " : AVRprog nadal wyświetla powyższy komunikat.
Bascom zawiesił się w tym samym monecie co przedtem, lecz zauważyłem ze dioda "zielona" która powinna świecić się przy programowaniu świeci 2 sek i gaśnie na 2 sek i tak cały czas.
AVR STUDIO nadal wyświetla powyższy komunikat.
ps. sorki za sposób umieszczenia grafiki ... zaraz poprawie Źródło: dioda.prohost.pl/forum/viewtopic.php?t=3642
zanotowane.pldoc.pisz.plpdf.pisz.plprojektlr.keep.pl
|
|
Cytat |
Dla aktywnego człowieka świat jest tym, czym powinien być, to znaczy pełen przeciwności. Luc de Clapiers de Vauvenargues (1715 - 1747) Ignorancja nie jest niewinnością, jest grzechem. Browing R Actus hominis, non dignitas iudicetur - niechaj sądzone będą czyny ludzkie, nie godności (piastowane stanowiska). (piastowane stanowiska). (piastowane stanowiska) Jak trudno stać się prawdziwym człowiekiem. Lecz komuś, kto się nim stanie, łatwo rozpoznać Boga. Kirpal Singh Gdy lód rusza bałwany tracą głowę. Regulski Antoni
|
|