|
Nienawidzę być kurą domową
|
Temat: [Audi A6 C5] diagnostyka silnika 2,5 TDI skoro pytasz o diagnoze to domyślam się że dysponujesz interfejsem i programem vag-com.
Jesli chodzi o sam silnik, to rozgrzej go do temperatury roboczej (minimum 87 stopni - to nie jest konieczne do sprawdzenia samych błędów ale do wykonania logów - tak), następnie w vagu wejdź w 01-silnik; potem w 02 - fault codes - w ten sposób sprawdzisz czy masz jakieś błędy. Jeśli bedą - zapisz je gdzieś do notatnika (mogą się przydać później), po czym skasuj je i zobacz czy coś ponownie sie pojawi - jesli tak - znów zapisz.
Następnym krokiem są tzw. logi. W celu ich wykonania wchodzisz w 08-measuring blocks i uruchamiasz potrzebne ci kanały. Są 3 rodzaje logów:
- statyczne - warunki: silnik rozgrzany do min. 87 stopni pracujący na biegu jałowym na... Źródło: a6klub.pl/viewtopic.php?t=11916
Temat: kody błędów Łukasz - masz te kody - wklej jak mozesz :] -wiem wykorzystuje ,ale ty wiesz gdzie to ja wklejam tylko kawałeczek.
FAULT CODE IDENTIFICATION
/ 1g OBD I - ECU FAULT CODES Electronic Control Unit
11 - Oxygen (O2) Sensor. Possible causes: faulty O2 sensor, connector or harness, low or high fuel pressure, defective injector(s), intake air leaks.
12 - Airflow Sensor. Possible causes: faulty airflow sensor, connector or harness.
13 - Intake Air Temperature Sensor. Possible causes: faulty intake air temperature sensor, connector or harness.
14 - Throttle Position Sensor (TPS). Possible causes: faulty TPS,... Źródło: forum.mitsumaniaki.pl/viewtopic.php?t=35816
Temat: [A6/C4 ABC 2,6 150 KM] Błąd immo (identyfikacja błędu) Głównie zastanawia mnie ta kwestia '07-10 - Signal to Low - Intermittent' która powtarza się zarówno przy immo i poduchach.
Co do poduszek to błąd wyrażony jest jako: "Przekaźnik przekładni - zła masa, niskie napięcie zasilania", czyli jest to zasadniczo kwestia podłączenia instalacji? Zasilanie?
I jeszcze chciałbym się upewnić. Korzystam z vag-com 311.2
Wybieram, kody błędów (u mnie to ' fault codes' z tego co pamiętam) i następnie 'clear codes'. To jest kasowanie błędów czy tylko kasowanie ich wyników z pola w programie które to wyświetla?
Jeżeli usuwanie to nawet po usuwaniu wywalą tą część z immo.
Pozdrawiam Źródło: a6klub.pl/viewtopic.php?t=22090
Temat: [A6 C5 1.9TDI][ auto] Problem ze skrzynią ...że to przeguby, bo podobny odgłos, lecz gdy wrzuciłem R okazało się, że auto nie jedzie do tyłu. Dziś auto nie wydaje już tych dziwnych dzwięków, lecz ciągnie wyraźnie słabiej, biegi załącza nieco inaczej, z opóźnieniem i wstecznego nie ma nadal.
Ktoś z Was wie co mogło się stać?
Autko ma nalatane zaledwie 110 tys km jest to zwykły automat.
Olej w skrzyni był zmieniany wraz z filtrem jakieś 12 tys km temu.
Podpiąłem VAGa, (no fault codes found)
Bardzo proszę o jakiekolwiek sugestie Źródło: a6klub.pl/viewtopic.php?t=8155
Temat: Potrzebny tłumacz... ...punktów. Ja jestem taki cienki że nie potrafię tego sensownie przetłumaczyć. Te tłumaczenia dam do tematu http://forum.tempra.org/t...0185.htm#102672 i będzie wszystko tak jak powinno być. Z góry dziękuję.
43 Primary ignition (distributor systems) High voltage
46 Amplifier (Direct Ignition System (DIS)) control signal (A+B) High voltage
51 Engine Control Unit (ECU) Defective ECU (disconnect and reconnect (ECU), then echeck for fault codes). Memory failure
54 Idle Carbon Monoxide (CO) potentiometer n/a
55 Engine Control Unit (ECU) fault Renew Engine Control Unit (ECU)
56 Air control soleniod Low voltage
57 Air control soleniod High voltage
63 Amplifier control signal, cylinders 2 and 3 (Direct Ignition System (DIS)) Low voltage
64 Amplifier control signal, cylinders 1 and 4 (Direct Ignition System (DIS)) Low voltage
65 Primary ignition (distributor systems) Low... Źródło: forum.tempra.org/viewtopic.php?t=10214
Temat: Kod B3601 i B3794 pomocy ??? ...potrafi rozszyfrowac te dwa kody B3601 i B3794 ??
Znalazlem w internecie opis pierwsego... ale co to oznacza ??? :confused:
B3601 - holding magnetic key relay circuit malfunction AF 17-4 Automatic 4-speed gearbox C-005
Odczyt z diagnozy wygladal tak:
______________________________________________
OP-COM 070209 - PC based diagnostic tool
Control Unit:
Part Number: 13132475_
Vehicle VIN:W0L0Z............
Identifier:0x0008
Total number of fault codes: 2
B3601 - Key Capture Relay Circuit Malfunction
(04) - Present
B3794 - <Unknown DTC>
(08) - Not present
________________________________________________
Dziekuje za wszelka pomoc
Pozdrawiam Alex Źródło: forum.vectra-unlimited.pl/showthread.php?t=44937
Temat: [A6 C5]Parktronic A6 C5 Avant 2001 vorlift- diagnoza ...Możesz sprawdzić też'' na dotyk''.
Włącz zapłon,wsteczny,dotknij palcem po kolei czujki.te sprawne będą lekko ''pulsowały''.Na pewno to wyczujesz.
U mnie ta metoda na 100% pokrywa się z odczytem z vag-prawa środkowa tył jest uszkodzona.
Tak jak w Twoim przypadku nie mogę dostać się do tych czujników(nie chce czegoś zniszczyć.)
Co do sprawdzenia vag-iem
-select
-wchodzisz w zakładke Electronics 1
-wciskasz 76-Park Assist
- Fault codes Źródło: a6klub.pl/viewtopic.php?t=10891
Temat: [100/A6 C4][2.5 TDI AAT AEL][HowTo]Spr i Zmiana kąta wtrysku Witam
Na początek pokaże jak sprawdzić kąt wyprzedzenia zapłonu. Za materiał podziękowania dla elmi_k
1. przy robieniu silnik ma być nagrzany do temp. roboczej ~90 stopni
2. Jak fejs połączy się z autem dajesz:
>Select
>Engine (z czyta wartości ze sterownika, kodowanie itd.)>
> Fault Codes(sprawdzasz czy w pamięci nie ma zapisanych błędów)
>Meas.Blocks> i pojawiają Ci się 3 wiersze
W pierwszym od razu masz ustawiony kanał "000" i wciskamy GO (druga wartość to jest wartość kąta wtrysku, ) możesz dawać kolejne kanały, np. 001, 002, 003
Jeżeli chcesz zobaczyć jaka masz wartość kata w BS kliknij na dole Switch to Basic Settings, automatycznie zwiększy Ci obroty do 1000 bądź 1200 w... Źródło: a6klub.pl/viewtopic.php?t=12329
Temat: duży apetyt na benzyne w mojej MX-5 mam w kompie aczkolwiek co oznacza błąd 8 szybkich i 1 długi bo nadal nikt mnie nie oswiecił
Jeden wolny osiem szybkich jeśli już
Ciekawe bo w normalnych fault codes z miata.net nie ma...
Jeśli Cię to pocieszy, od dwóch lat próbuję się dowiedzieć co oznacza kod 48 w systemie SRS poduch powietrznych - też nie mogę znaleźć Źródło: miata.com.pl/viewtopic.php?t=4347
Temat: Wymieniony przepływomierz, sonda lambda i jednak coś nie tak ROCKY_AGH,
18001/P1593/005523 - Altitude Adaptation: Signal Out of Tolerance
Possible Symptoms
Unknown
Commentary
This is one of those fault codes where the ECU knows something is amiss, but cannot pinpoint the cause.
Possible Causes
MAF sensor (G70) out of tolerance.
Leak in intake system.
Throttle position sensors (G187/G188) out of tolerance.
Possible Solutions
Check MAF/replace MAF Sensor (G70).
Check intake systems for leaks and repair.
Check Throttle position sensors (G187/G188)
17544/P1136/004406 - Fuel Trim: Bank 1 (Add): System too Lean
Possible... Źródło: leonclub.pl/forum/viewtopic.php?t=20044
Temat: diagnostyka silnika tdi ...- diagnostyka czyni cuda .
Diagnostyka silnika właściwa.
Diagnostykę wykonujemy trójetapowo:
1. poprzez odczyt błędów;
2. poprzez odczyt bloków wartości mierzonych:
a. w tzw. próbie statycznej;
b. w tzw. próbie dynamicznej.
Po uruchomieniu programu VAG-Com wykonujemy następujące operacje:
1. dla odczytu błędów w sterowniku silnika [ECU]:
Select [z okienka Select Control Module] > 01-Engine > 02- Fault Codes
po czym zapisujemy wyświetlone błędy [o ile w ogóle są] do pliku .txt i oczywiście zamieszczamy na forum.
2. dla odczytu bloków wartości mierzonych:
Select [z okienka Select Control Module] > 01-Engine > 08-Meas. Blocks [bloki wartości mierzonych].
a. próba statyczna
warunki konieczne: samochód stoi na biegu jałowym; silnik włączony; robocza temperatura silnika - temperatura płynu chłodzącego min.... Źródło: pkaudi.pl/forum/viewtopic.php?t=121
Temat: Kody błędów Motronic http://e30world.com/fuel/...nic-fault-codes Źródło: e12e28.pl/viewtopic.php?t=3796
Temat: VAG Kody błędów 16685 00896 Witam dzieki za pomoc ,właśnie wróciłem z garazu i doszły nowe ciekawostki oprocz błędu 16685 pojawił się nowy ale nie w sterowniku silnika tylko pod adress 03 (ABS)
01314 Engine Control Module 79-00 please check fault codes.Sprawdziłem z ciekawości
blok pomiarowy grupa 000 i taka ciekawostka wszystkie parametry w normie poza 5 Kąt przepustnicy podają 2...10 a u mnie 008 więc może jest to sprawa szczelnosci o której piszesz .Jeszcze tam nie zaglądałem adaptacje robiłem chyba ze 2x ,więc czas nabyć uszczelki i wymyć przepustnice. Pozdrawiam Jacko Źródło: fabiaclub.pl/forum-pl/viewtopic.php?t=4771
Temat: [A6 C6] Migajaca kontrolka swiec zarowych Blad 009263 ...inna?
Particle Filter Emergency Regeneration
Prerequisites:
Ignition ON
Engine ON (Idle)
Oil Temperature above 70 °C (see MVB 007.2)
Particle Filter Load below 68g (see MVB 104.3)
If the Particle Filter Load is above 68g the Particle Filter needs to be replaced since the car may burn down when regenerating.
Engine Hood CLOSED
Parking Brake ENGAGED
Transmission in (P)ARK
Temperatures at the Exhaust System may rise up to 300 °C!!!
No Fault Codes Stored
Power Consumers ON (Light, Seat Heating, Front/Rear Window Heater, Climate Control)
The Regeneration may take up to 40 minutes, the engine speed automatically increases to about 1500 RPM.
[Select]
[01 - Engine]
[Coding-II - 11]
Start Regeneration by Entering 10016.
[Do It!]
[Meas. Blocks - 08]
Select all 3 Groups at once 100, 101 and 102
[Go!]
MVB 100.1: Engine Speed
MVB 100.3: Regeneration... Źródło: a6klub.pl/viewtopic.php?t=19265
Temat: [A6 C4 2,5 TDI] proszę o analizę błędów bo ja jestem zielony yyy to nieznasz podstaw jak sie kasuje błędy ?
- podałes wyres ktory zrobiles poprzez - taka jakby analizę ogólną
teraz zeby pokasować te błędy musisz wejsc w poszczegolne dzialy w vagu-
1 zeby wejsc w silnik klikasz na engine potem fault codes a nastepnie przycisk clear faults i tak robisz z każdym działem np klima itd ,abs itd, pp itd Źródło: a6klub.pl/viewtopic.php?t=19776
Temat: [F1] Niepokojąca praca silnika przy odkręconym korku oleju ...- Long Term Fuel Trim Additive Air Bank 1: Range 2: System too Lean
P1152 - 35-10 - - - Intermittent
16825 - EVAP Emission Control Sys: Incorrect Flow
P0441 - 35-10 - - - Intermittent
17961 - Barometric / Manifold Pressure Signals: Implausible Correlation
P1553 - 35-10 - - - Intermittent
Address 03 -------------------------------------------------------
Component: ABS 5.7 FRONT V40
1 Fault Found:
01314 - Engine Control Module
79-10 - Please Check Fault Codes – Intermittent
Błędy skasowałem i silnik pracuje normalnie, ale dziwni mnie ta sytuacja ponieważ jakiś czas temu odkręcałem korek od oleju przy pracującym silniku i takich „cyrków” nie było.
Macie jakieś pomysły?
Krzysiek Źródło: fabiaclub.pl/forum-pl/viewtopic.php?t=6881
Temat: Kto robil odczyt bledow z kompa VectA? ja mam Simtec (X20XEV) i mam 10 (2 razy po 5) zlaczy. Nie bylem pewnien co tam jest A i B ale znalazlem dokladna instrukcje na www.topbuzz.co.uk (sekcja Informations i Reading ECU Fault Codes)... thx a lot za odpowiedz Źródło: forum.vectra-unlimited.pl/showthread.php?t=27196
Temat: Wymiana pompy ABS ...wymianę pompy weźmie 100zł, do tego wymienię jeszcze klocki i płyn hamulcowy. Pompę, którą kupiłem podłączałem już pod wtyczki w aucie, kontrolka pomigała i zgasła, więc chyba z nią wszystko ok (przynajmniej elektrycznie).
Z tą diagnostyką to jakaś lipa, pisałem wcześniej, że można to zrobić samemu, podobnie jak diagnostykę sterownika silnika. Podpina się lampkę i 12V do wtyczki diagnostycznej i lampka sobie miga. W autodacie są fault codes, czyli kody błędów dla ABSu. Wtyczka jest u mnie włożona w takie plastikowe miejsce przy skrzynce bezpieczników w komorze silnika. Jak coś to naszkicuję odpowiedni układ.
Nie jestem mechanikiem a o tym wiem.
Pompa wymieniona, wszystko działa jak powinno. Auto znowu super-lux Źródło: 306team.pl/forum/viewtopic.php?t=431
Temat: [A6 C5 2.5 TDI ] Brak mocy silnika - nie tylko ciśnienia ? ...testy w próbie dynamicznej (b)
Diagnostyka silnika właściwa.
Diagnostykę wykonujemy trójetapowo:
1. poprzez odczyt błędów;
2. poprzez odczyt bloków wartości mierzonych:
a. w tzw. próbie statycznej;
b. w tzw. próbie dynamicznej.
Po uruchomieniu programu VAG-Com wykonujemy następujące operacje:
1. dla odczytu błędów w sterowniku silnika [ECU]:
Select [z okienka Select Control Module] > 01-Engine > 02- Fault Codes
po czym zapisujemy wyświetlone błędy [o ile w ogóle są] do pliku .txt i oczywiście zamieszczamy na forum.
2. dla odczytu bloków wartości mierzonych:
Select [z okienka Select Control Module] > 01-Engine > 08-Meas. Blocks [bloki wartości mierzonych].
a. próba statyczna
warunki konieczne: samochód stoi na biegu jałowym; silnik włączony; robocza temperatura silnika - temperatura płynu chłodzącego min.... Źródło: a6klub.pl/viewtopic.php?t=3625
Temat: Błąd 01314 ...Module faulty
* Fault(s) stored in Engine Control Module
Possible Solutions
* Check CAN-Databus Wiring/Connectors from/to Engine Control Module
* Check Measuring Value Blocks (MVB)
o Usually Measuring Value Blocks (MVB) 125+ show the current Communication Status
01314 - Engine Control Module: Check DTC Memory
Possible Causes
* Fault(s) stored in Engine Control Module
Possible Solutions
* Check Engine Control Module for Fault Codes
Special Notes
* Engine Control Module stored a Code which influences other Control Modules Functionality.
* To clear this Fault Code you will need to correct the Problem in the Engine Control Module first. Źródło: leonclub.pl/forum/viewtopic.php?t=22844
Temat: [a6 c5 2.5 tdi] interpertacja błędów fault codes - i jak się jakieś wyświetlą - clear (lub delete - nie pamiętam ) codes Źródło: a6klub.pl/viewtopic.php?t=15124
Temat: ABS i błędy 01314 00597 00283 01316 01054 ...tak jak próbowałbym hamować na śliskiej nawierzchni. Niestety kontrolka już nie zgasła, pali się cały czas, sam system ABS przestał działać.
Wybrałem się do zaprzyjaźnionego Forumowicza podpiął mnie pod VAG-a i oto lista błędów
Control Module Part Number: 6Q0 907 379
Component and/or Version: ABS 5.7 FRONT V00
Software Coding: 00036
Work Shop Code: WSC 13765
3 Faults Found:
01314 - Engine Control Module
79-10 - Please Check Fault Codes - Intermittent
00597 - Wheel Speed Impulses: Deviation
35-10 - - - Intermittent
00283 - Front Left ABS Wheel Speed Sensor (G47)
35-00 - -
VAG-COM Version: Release 303.1
Control Module Part Number: 6Y1 919 880 C
Component and/or Version: KOMBIINSTRUMENT VDO V06
Software Coding: 16141
Work Shop Code: WSC 30295
Additional Info: TMBNB26Y5Y3015743 SKZ7Z0X0400765
1 Faults Found:
01316 - ABS Control Module
49-10 - No... Źródło: fabiaclub.pl/forum-pl/viewtopic.php?t=4262
Temat: Chevrolet Europe TIS 2009 iso EPC ...EPC, jest aplikacją oprogramowania.
Niniejszą aplikację stworzył General Motors dla wygody swoich użytkowników, którzy próbują znaleźć informacje o częściach do samochodów produkowanych przez GM Europe.
In the catalog of Chevrolet TIS Europe will get comprehensive information in ten languages to build Chevrolet Europe: guidelines for the repair,
maintenance, diagnostics, wiring diagrams, body dimensions, decoding diagnostic fault codes DTC (Diagnostic Trouble Codes), as well as standard chasy.
Katalog Chevrolet TIS Europe.
DOSTĘPNE JĘZYKI :
CZ, D, GB, GR, H, HR, PL, RO, RUS, TR
MODELE
Matiz 2006-2009
Kalos/Aveo 2006-2009
Nubira/Lacetti 2006-2009
Cruse 2010
Takuma 2006-2009
Evanda/Epica 2006-2009
Captiva 2007-2009
Rok: 2009
Rozmiar: 1.95 GB
System: Windows 98,ME,XP i Vista
Chevrolet Europe TIS 2009 iso EPC
Party... Źródło: ultrablackwarez.boo.pl/viewtopic.php?t=1850
Temat: Wirus kasujący pliki na dysku comment5, daihatsu rocky transmission transfer cases, >:-]]], daihatsu kancil timing belt, pki, daihatsu sirion fuses, 032, daihl towson state, jpvyt, daihatsu horbury bridge, 41291, daikin fault codes, =-)), daihatsu pulls out, csvew, daikin ac, 8]], daiichi pharmaceuticals uk ltd, , daiki mori, 795, [/url], =OOO, [url=http:...ir conditioners, 876, daikai, 709, daikin code 50, fawj, daihatsu mira service manual l201, =O, daihatsu mower, icqkrq, daihatsu official website, ynzots, Źródło: gangstar.ok1.pl/viewtopic.php?t=161
Temat: Honda ALB2 ABS Computer - Fault Codes Fault codes: how to access.
Turn igniton off. (Wyłącz zapłon)
Bridge diagnostic socket terminals. (zmostkuj połaczenie w złaczce swrwisowej - ta sama co do samodiagnostyki silnika )
Turn ignition on. (włącz zapłon)
If ecu is ok warning should come on for 2 seconds and then go out for 2 seconds. (jezli ECU od ABS jest OK lampka ABS zapali sie na 2 sekundy)
The lamp should then begin to flash. (jezli sa błędy to lampka zacznie migac)
The first... Źródło: jdm-option.pl/forum/viewtopic.php?t=629
Temat: problem z instalacja holenderska ...system. The lambda control system of the original petrol fuel management is thus also the lambda control system of the YPS system and the OBD (II) system remains entirely operational both on petrol and on gas.
YPS has it's own diagnostic system. The driver is warned by sound signals and visually by lighting LED's when the emissions are out of limits and when the gas level in the storage tank is too low. In which case the vehicle is automatically switched to petrol. The fault codes are saved and can be monitored. Źródło: forum.mitsumaniaki.pl/viewtopic.php?t=11874
Temat: po rozgrzaniu muli 1.8is The fault codes for these systems will appear on the check engine light when you turn the ignition key to the On position (but don't start it), then: fully depress the accelerator pedal, then fully release it. Repeat the depress, release cycle 5 times fairly quickly, but not too fast. It should be completed in a few seconds.
OK przekrecam na zaplon stacyjke, nie zapalam, przyciskam pedal gazu na maxa i puszczam do pozycji poczatkowej piec razy, ... nawet nawet... Źródło: forum.beemka-klub.pl/viewtopic.php?t=11307
zanotowane.pldoc.pisz.plpdf.pisz.plprojektlr.keep.pl
|
|
Cytat |
Dla aktywnego człowieka świat jest tym, czym powinien być, to znaczy pełen przeciwności. Luc de Clapiers de Vauvenargues (1715 - 1747) Ignorancja nie jest niewinnością, jest grzechem. Browing R Actus hominis, non dignitas iudicetur - niechaj sądzone będą czyny ludzkie, nie godności (piastowane stanowiska). (piastowane stanowiska). (piastowane stanowiska) Jak trudno stać się prawdziwym człowiekiem. Lecz komuś, kto się nim stanie, łatwo rozpoznać Boga. Kirpal Singh Gdy lód rusza bałwany tracą głowę. Regulski Antoni
|
|